Skidsteer tiller motor (2024)

I have a JCT tiller and the motor is bad, I am not having any luck finding a replacement motor. Jct will not reply to my email, that is the only to contact them. Anybody know of a good place to find a motor that will work. From what I can find this motor is a hmsj-400 specs below.

Could try here:

DFS2005 said:

I have a JCT tiller and the motor is bad, I am not having any luck finding a replacement motor. Jct will not reply to my email, that is the only to contact them. Anybody know of a good place to find a motor that will work. From what I can find this motor is a hmsj-400 specs below.

View attachment 1577

Click to expand...

Hello

Do you still have the old Orbital motor off of your JCT tiller?

In need of Orbital Motor said:

Hello

Do you still have the old Orbital motor off of your JCT tiller?

Click to expand...

I am just needing the output shaft.

DFS2005 said:

Yes I still have it. Not for sure what they call it but the shaft inside the motor was broken. This is a new tiller never used, my guess the motor broke when they tested it at the factory. Its doubtful I will hear from JCT or that they will warrantee the motor but I would like to hold onto it for a bit longer just incase they do.

Click to expand...

I bought a brand new tiller at an auction and the output shaft is broken. Looks like it fell off the delivery truck or something. It also broke the pillow block at the other end. Not sure if we would be able to put our to Orbital Motors together and make a good one or not. I am unable to get ahold of JCT as well.

I ended up buying this one from surplus center, matches pretty close to the jct motor.

T

DFS2005 said:

I ended up buying this one from surplus center, matches pretty close to the jct motor.

24.36 cu. in. / rev. Danfoss 355400AH321BAAAAP Hydraulic Motor 11200557 | Low Speed High Torque Hydraulic Motors | Hydraulic Motors | Hydraulics | www.surpluscenter.com

24.36 cu. in. / rev. Danfoss 355400AH321BAAAAP Hydraulic Motor 11200557, Low Speed High Torque Hydraulic Motors, 24.36 cu. in. DANFOSSDanfoss,355400AH321BAAAAP,

www.surpluscenter.com

Click to expand...

Thanks for the Link! That one is a lot cheaper than the ones I have been looking at. Does your tiller work pretty good? My internal shaft is fine. I am in Ohio.

DFS2005 said:

I have yet to use it. The new motor is supposed to be here today. Then I will have to wait for things to dry out its done nothing but rain or snow for the last few weeks.

Click to expand...

Hello,

Did you get your tiller to till up some ground yet?

In need of Orbital Motor said:

Hello,

Did you get your tiller to till up some ground yet?

Click to expand...

I tried it briefly after I got the motor on, but the ground was still pretty wet. My plan is to do some tilling this weekend.

DFS2005 said:

thanks I was able to find a motor that should work.

Click to expand...

Can you let me know where you were able to find a matching motor. I bought a JCT and need a replacement HMSJ-400 Orbit for my rotor tiller & a HMS-160 Orbit for my brush hog. I tried the surplus Center mentioned in the thread and nothing came up on their site with these model numbers. thank you.

DFS2005 said:

I have a JCT tiller and the motor is bad, I am not having any luck finding a replacement motor. Jct will not reply to my email, that is the only to contact them. Anybody know of a good place to find a motor that will work. From what I can find this motor is a hmsj-400 specs below.

View attachment 1577

Click to expand...

Sorry to hear it. I have had problems with my tiller and I have a post showing pictures how The blades fell off bolts loosened and blades were bent badly. My post shows the pictures and JTC. Never got back to me either. My next step would be to contact the customs department of the US because I think these are being shipped into United States and the JTC name it just a front. Not sure, but that's one way to find out and the more people that do it. Contact customs will stir the pot. Did you have any Other problems Van

DFS2005 said:

I tried it briefly after I got the motor on, but the ground was still pretty wet. My plan is to do some tilling this weekend.

Click to expand...

Which motor did you order, did it work?

I was able to find a replacement motor for my JCT brush hog that fit into the original bracket (with 2 bolts instead of the original 4). I should have gotten it with a longer shaft, but the coupler just barely bridges the distance. I use the coupler instead of the lovejoy set up they originally had. I don't know if that will be a problem in the long run or not, but so far it is working. Right now I am just cutting grass and high weeds.

The coupler did slide off on me, so I put a bolt (not pictured) through the hole which only puts the coupler on the edge of the PTO type shaft on the gear box, but it puts the other end against the new motor wall so it does not slide anymore.

I needed new hoses as the JCT hoses did not match anything in the US or Europe (guess where it came from).

I bought both the motor and the coupler from www.surpluscenter.com for about $400 with shipping and tax, plus the new hoses from a local hose place. The parts I bought are item numbers 9-7078-160 and 1-2459. Surpluscenter sales support were very helpful. Ask them if the motor comes with a longer shaft version.